救命呀! 重灌XP後, 所有備份硬盤全無資料顯示 (有圖)

[Henry]

救命呀! 重灌XP後, 所有備份硬盤全無資料顯示 (有圖)

(XP電腦為DELL Dimension 4600) (視窗2000 Pro電腦為不知品牌名的電腦)

1. 放入XP的安裝碟.
2. 關電腦, 刪除兩個備份硬盤, 還剩C:盤未被刪除.
3. 開電腦, 按F2到BIOS時才關掉此兩備份硬盤, 調整CD碟片機為優先啟動, 調整可准許重灌XP.
4. 安裝完XP後, 關電腦, 把兩備份硬盤裝回原電腦.
5. 開電腦, 按F2到BIOS調回此兩備份硬盤為AUTO, 調回C:硬盤為優先啟動, 調回為不可重灌XP.

可能以上第2及第3步驟有所調亂弄錯而造成BIOS不能再確認巳有舊有資料檔案地址在全部3隻硬盤, 故此在”我的電腦”中衹顯示部份未格式化的硬盤容量.
在巳重灌Windows XP電腦中的”電腦管理”並無任何硬盤”未安置”的顯示, 故此將此3個出事的硬盤分別的放於Windows 2000 Pro (視窗2000)為副硬盤儉看時, 才發現到在Windows 2000 Pro電腦中的”電腦管理”內有硬盤部份”未安置”的顯示. 如圖所示如下:



註: 我巳參考過 http://www.pcview.org/forum/viewtopic.php?t=438 的 “新安裝的硬碟不在"我的電腦"出現” 的話題了 , 但此個是安裝新硬盤, 而現時的是要挽留及再顯示無意被分區的硬盤並要在原有不顯示 “未置位unallocated” 的Windows XP電腦中把硬碟重灌Windows XP. 在技術上看來較為前者復雜.



Please rescue the lost data back up hard drive

Help! After re-installed Windows XP, all hard drives do not show up any back up data again. (Illustrations are shown below.)

(Dell Dimension 4600 runs with Windows XP)
(Another un-known brand name computer runs with Windows 2000 Pro)

1. Inserted Windows XP CDROM for installation.
2. Turned OFF computer, physically disconnected 2 backup hard drives, and kept C: drive only still connecting with computer.
3. Turned ON computer, pressed F2. While BIOS was running, then sat OFF both backup hard drives, sat CDROM as the first drive, and sat the permission of system operational installation ON.
4. After Windows XP had been installed, turned OFF computer, physically re-connected both backup hard drives into the original computer.
5. Turned ON computer, pressed F2. While BIOS was running, sat both backup hard drives back to AUTO, sat back C: drive as the first drive, and sat back the permission of system operational installation OFF.

Step 2 and 3 as describing above might be wrong in procedure. So, BIOS could not recognize the address of the old data within all 3 hard drives again, causing “My Computer” only shows out the partial memory volume of the drives individually.
The computer that had been re-installed with Windows XP does not show out any “un-located” region from “Computer Management”. So, all 3 individual wrongful hard drives were placed into another computer which runs Windows 2000 Pro, then the “un-located” regions are showing in “Computer Manager”.

Please let me know how the lost backup data inside these 2 backup drives can be shown out again. Please rescue my fault. The whole thing collapse was caused by one step mistaking.

[Henry]

前文再續講到巳把原為處在Windows XP的硬盤C:放到行使着Windows 2000 Pro的叧一電腦作為副硬盤E:時, 在其 “電腦管理Computer Management” 處發現在E:硬盤旁還有 “未置位Unallocated” 的顯示 (在Windows XP的 “電腦管理並無此 “未罝位” 的顯示).

註: 我巳參考過 http://www.pcview.org/forum/viewtopic.php?t=438 的 “新安裝的硬碟不在"我的電腦"出現” 的話題了 , 但此個是安裝新硬盤, 而現時的是要挽留及再顯示無意被分區的硬盤並要在原有不顯示 “未置位unallocated” 的Windows XP電腦中把硬碟重灌Windows XP. 在技術上看來較為前者復雜.

根據我朋友的簡單電郵回覆, 原文如下:
You need to right click on My Computer and click on Manage. Then look for Disk Manager. From there, it should show you all the drives you have attached to the computer. What you need to go from there is assign the unallocated drives a letter.

意譯為:
你需要在 “我的電腦My Computer” 處右按鼠標來選擇 “管理Manage”, 後再找尋 “磁盤管理Disk Manager”. 在這處, 你應將會看到所有附設在電腦內的磁盤drives, 在那處你應需要去做的就是把 “未置位Unallocated” 的磁盤給予它一個英文字母.

跟着我便依從着以上的指示瞎目的做了以下圖示的工作:

希望站長及各前輩見議我應選擇 “Primary partition” 或是 “Extended partition” 及接着以後的步驟我應要怎樣去做呢. 懇請站長及各前輩賜教. 多謝.

我全文的要求做作是為了:
1. 顯示所有藏於原為Windows XP的C: 硬盤及其它兩個備份硬盤裏不能再開啟的舊有重要備份資料. (後把資料另存備份)
2. 把巳無意被分區的Windows XP的C: (在Windows 2000 Pro時為E: 硬盤) 硬盤內所有的分區覆合為原有的一個總區500GB. 後再安裝回原有的Windows XP電腦作重灌Windows XP.
3. 把巳無意被分區的Windows XP的兩個備份硬盤 (一為400GB的SATA硬盤, 另一為500GB的ATA硬盤), 最好能夠在覆合分區還原到一體的400GB及500GB後, 所有的備份還能存在及顯示.

[hammer]